Listed below are some interactive CCNA tutorials. Each tutorial explains the key concepts in a concise and easy-to-read language. Each course includes a pre-assessment, course map and post-assessment.

• Subnetting
• Layered Communication Models: OSI, TCP/IP & Cisco
• IP Addressing Tutorial
• Hex & Binary Tutorial

*CCNA Subnetting Tutorial (Click Here)

A short IP subnetting tutorial. Subnetting is explained with examples. Post assessment exercises after the course gives you hands on practice.By the end of this subnetting course, you should be able to:

• Define subnet and subnet masks
• Understand IP subnetting maths
• Calculate Network address
• Define private address
• Subnet an IP network in a given scenario

*OSI & TCP-IP Tutorial (Click Here)

A short course on layered communication models including the OSI Reference Model, TCP/IP Model and the Cisco’s Three Layered Hierarchical Model. The broad course of objectives are:

• Need for network layers
• ISO OSI reference model & it’s 7 layers of network
• TCP IP Model and it’s relation with 7 layer OSI model
• Cisco 3 layer hierarchical model
• Post assessment quiz on OSI

*IP Addressing Tutorial (Click Here)

Tutorial on understanding IP addressing. The broad course of objectives are:

• Learn IP addressing fundamentals
• Types of Addresses: Physical, IP & Port addresses
• Relationship of OSI Layers and Addresses in TCP/IP
• Special Addresses: Unicast, Multicast & Broadcast
• Notations of IP Addressing
• Classes of IP Addressing Explained
• LoopBack & Private IP Address
• Determining the Class of an Address
• Extracting Net id and Host id
• IP Address Decimal and Binary Conversions
• Special Addresses
• Sample Internet
• IP Versions: Ipv6 and Advantages
• DNS

*Binary & Hex Tutorial (Click Here)

Tutorial on understanding Decimal, Hex and Binary Number Systems. The broad course of objectives are:

• Decimal Number System
• Binary Numbers Tutorial Introduction
• Binary Numbers and Internet
• Convert Decimal to Binary
• Converting Binary to Decimal
• Similarity between Decimal and Binary Systems
• Hexadecimal Tutorial Introduction
• Hex to decimal conversion table
• Hexadecimal Numbering System
• Decimal to Hex conversion introduction
• How to convert Decimal to Hex
• How to convert hex to decimal
• IP Addresses in Hexadecimal Notation

Ethernet over IP (EoIP) Tunneling is a MikroTik RouterOS protocol that creates an Ethernet tunnel between two routers on top of an IP connection. The EoIP interface appears as an Ethernet interface. When the bridging function of the router is enabled, all Ethernet level traffic (all Ethernet protocols) will be bridged just as if there where a physical Ethernet interface and cable between the two routers (with bridging enabled). This protocol makes multiple network schemes possible.

Network setups with EoIP interfaces:

• Possibility to bridge LANs over the Internet
• Possibility to bridge LANs over encrypted tunnels
• Possibility to bridge LANs over 802.11b ‘ad-hoc‘ wireless networks

An EoIP interface should be configured on two routers that have the possibility for an IP level connection. The EoIP tunnel may run over an IPIP tunnel, a PPTP 128bit encrypted tunnel, a PPPoE connection, or any connection that transports IP. Specific Properties:

• Each EoIP tunnel interface can connect with one remote router which has a corresponding interface configured with the same ‘Tunnel ID’.
• The EoIP interface appears as an Ethernet interface under the interface list.
• This interface supports all features of and Ethernet interface. IP addresses and other tunnels may be run over the interface.
• The EoIP protocol encapsulates Ethernet frames in GRE (IP protocol number 47) packets (just like PPTP) and sends them to the remote side of the EoIP tunnel.
• Maximal count of EoIP tunnels is 65536.

This is how to set up EoIP to bridge two (or more) Mikrotik routers for central PPPoE authentication

Using 2 routers called R1 and R2 that have an IP connection between them and R2 has 2 ethernet ports, i.e. you can ping rB from R1 and R1 from R2 where the R1 facing eth port is called eth1 and its other port is called eth2.

1. create a new EoIP tunnel on R1.
2. create a new EoIP tunnel on R2, where the tunnel ID is the same as the one on R1 but the MAC addreses are different.
4. create a new bridge on R1 and R2
3. add a PPPoE server to the Bridge on R1.
4. on R2 and add eth2 and the EoIP tunnel to the bridge.
5. put an IP address onto eth2 (any address seems to work, but it maybe better to use a different subnet for routing purposes).

Now you should be able to establish a PPPoE connection from a PC plugged into the eth2 port on router R2, this PPPoE connection will terminate on router R1.

This is not the most efficient method of using the available bandwidth on a network, but is perhaps easier than having a PPPoE A/C on every Mikrotik router and using RADIUS as you can just have PPP secrets setup on one router.

• pilihlah paket – paket dibawah ini untuk install OS Microtik :

System, dhcp, Advance Tools, RouTing, Security, Web – Proxy.

• ganti nama system sesuai dengan selera anda :

[admin@microtik] > system identity set name=warnet

Selanjutnya promt shell akan berubah menjadi :
Seperti yg anda inginkan :
[admin@warnet] >

• Ubahlah Password OS microtik anda dengan cara :

[admin@warnet] >user set admin password=………………………………

• aktivkan kedua Ethernet pada PC yang telah anda install OS Microtik :

[admin@warnet] >interface ethernet enable ether1
[admin@warnet] >interface ethernet enable ether2

• Berikan nama pada kedua ethernet untuk memudahkan konfigurasi :

[admin@warnet] >interface Ethernet set ether1 name=modem =====è Ethernet yg utk modem
[admin@warnet] >interface ethernet set ether2 name=local ===è Ethernet yg untuk ke HUB

• Masukan IP pada kedua landcard :

[admin@warnet] >ip address add interface=modem address= ( Diisi IP address dari ISP ) / netmask
[admin@warnet] >ip address add interface=lokal address= 192.168.0.1/255.255.255.0

• masukkan IP gateway yg di berikan dari ISP :

[admin@warnet] > ip route add gateway=10.11.1.1560

• SETTING DNS :

[admin@warnet] >ip dns set primary-dns=10.11.155.1secondary-dns=10.11.155.2

setelah itu coba ping semua IP yang telah di setting di atas.

[b][font=”]KONFIGURASI FIREWALL DAN NETWORK
ip firewall nat add action=masquerade chain=srcnat
ip firewall filter add chain=input connection-state=invalid action=drop
ip firewall filter add chain=input protocol=udp action=accept
ip firewall filter add chain=input protocol=icmp action=accept
[font=”]/ip firewall filter add chain=input in-interface=(ethernet card yg ke lan) action=accept
/ip firewall filter add chain=input in-interface=(ethernet card yg ke internet) action=accept

ip firewall filter add chain=input action=drop

ip web-proxy set enabled=yes src-address=0.0.0.0. port=8080 hostname=”” yahuu.net=yes parent-proxy=0.0.0.0:0 \
cache-administrator=”webmaster” max-object-size=4096KiB cache-drive=system max-cache-size=unlimited \
max-ram-cache-size=unlimited

ip firewall nat add chain=dstnat protocol=tcp dst-port=80 action=redirect to-ports=3128 /ip firewall nat add in-interface=modem
dst-port=80 protocol=tcp action=redirect
to-ports=3128 chain=dstnat dst-address=!192.168.0.1/24

================================================== ================

yang 3128 semuanya di ganti 8080 : caranya :

ip web-proxy set enable=yes
/ip web-proxy set port=3128
/ip web-proxy set max-cache-size=3145728 ( 3 kali total ram )
/ip web-proxy set hostname=”proxy.prima”
/ip web-proxy set allow-remote-requests=yes
/ip web-proxy set cache-administrator: “primanet.slawi@yahoo.com”
================================================== ================================================== ========
FILTERING :
http://www.mikrotik.com/testdocs/ros/2.9/ip/filter.php/ ip firewall filter
add chain=input connection-state=invalid action=drop \comment=”Drop Invalid connections”
add chain=input connection-state=established action=accept \comment=”Allow Established connections”
add chain=input protocol=udp action=accept \ comment=”Allow UDP”
add chain=input protocol=icmp action=accept \ comment=”Allow ICMP”
add chain=input src-address=192.168.0.0/24 action=accept \ comment=”Allow access to router from known network”
add chain=input action=drop comment=”Drop anything else”

ANTI VIRUS UTK MICROTIK :
add chain=forward action=jump jump-target=virus comment=”jump to the virus chain” ++++++++++++++++++++++++++++++++++++++++++++++++++ +++++

add chain=forward protocol=icmp comment=”allow ping”add chain=forward protocol=udp comment=”allow udp”add chain=forward action=drop comment=”drop everything else”================================================== =====

SECURITY ROUTER MICROTIK ANDA :
/ ip firewall filteradd chain=input connection-state=established comment=”Accept established connections”add chain=input connection-state=related comment=”Accept related connections”add chain=input connection-state=invalid action=drop comment=”Drop invalid connections” add chain=input protocol=udp action=accept comment=”UDP” disabled=no add chain=input protocol=icmp limit=50/5s,2 comment=”Allow limited pings” add chain=input protocol=icmp action=drop comment=”Drop excess pings” add chain=input protocol=tcp dst-port=22 comment=”SSH for secure shell”add chain=input protocol=tcp dst-port=8291 comment=”winbox” # Edit these rules to reflect your actual IP addresses! # add chain=input src-address=159.148.172.192/28 comment=”From Mikrotikls network” add chain=input src-address=10.0.0.0/8 comment=”From our private LAN”# End of Edit #add chain=input action=log log-prefix=”DROP INPUT” comment=”Log everything else”add chain=input action=drop comment=”Drop everything else”
“http://wiki.mikrotik.com/wiki/Securing_your_router“
================================================== ========================================
SETTING KEAMANAN JARINGAN HANYA UNTUK LOKAL AREA ANDA :
/ip firewall filteradd chain=forward connection-state=established comment=”allow established connections” add chain=forward connection-state=related comment=”allow related connections”add chain=forward connection-state=invalid action=drop comment=”drop invalid connections”
add chain=virus protocol=tcp dst-port=135-139 action=drop comment=”Drop Blaster Worm” add chain=virus protocol=udp dst-port=135-139 action=drop comment=”Drop Messenger Worm” add chain=virus protocol=tcp dst-port=445 action=drop comment=”Drop Blaster Worm” add chain=virus protocol=udp dst-port=445 action=drop comment=”Drop Blaster Worm” add chain=virus protocol=tcp dst-port=593 action=drop comment=”________” add chain=virus protocol=tcp dst-port=1024-1030 action=drop comment=”________” add chain=virus protocol=tcp dst-port=1080 action=drop comment=”Drop MyDoom” add chain=virus protocol=tcp dst-port=1214 action=drop comment=”________” add chain=virus protocol=tcp dst-port=1363 action=drop comment=”ndm requester” add chain=virus protocol=tcp dst-port=1364 action=drop comment=”ndm server” add chain=virus protocol=tcp dst-port=1368 action=drop comment=”screen cast” add chain=virus protocol=tcp dst-port=1373 action=drop comment=”hromgrafx” add chain=virus protocol=tcp dst-port=1377 action=drop comment=”cichlid” add chain=virus protocol=tcp dst-port=1433-1434 action=drop comment=”Worm” add chain=virus protocol=tcp dst-port=2745 action=drop comment=”Bagle Virus” add chain=virus protocol=tcp dst-port=2283 action=drop comment=”Drop Dumaru.Y” add chain=virus protocol=tcp dst-port=2535 action=drop comment=”Drop Beagle” add chain=virus protocol=tcp dst-port=2745 action=drop comment=”Drop Beagle.C-K” add chain=virus protocol=tcp dst-port=3127-3128 action=drop comment=”Drop MyDoom” add chain=virus protocol=tcp dst-port=3410 action=drop comment=”Drop Backdoor OptixPro”add chain=virus protocol=tcp dst-port=4444 action=drop comment=”Worm” add chain=virus protocol=udp dst-port=4444 action=drop comment=”Worm” add chain=virus protocol=tcp dst-port=5554 action=drop comment=”Drop Sasser” add chain=virus protocol=tcp dst-port=8866 action=drop comment=”Drop Beagle.B” add chain=virus protocol=tcp dst-port=9898 action=drop comment=”Drop Dabber.A-B” add chain=virus protocol=tcp dst-port=10000 action=drop comment=”Drop Dumaru.Y” add chain=virus protocol=tcp dst-port=10080 action=drop comment=”Drop MyDoom.B” add chain=virus protocol=tcp dst-port=12345 action=drop comment=”Drop NetBus” add chain=virus protocol=tcp dst-port=17300 action=drop comment=”Drop Kuang2″ add chain=virus protocol=tcp dst-port=27374 action=drop comment=”Drop SubSeven” add chain=virus protocol=tcp dst-port=65506 action=drop comment=”Drop PhatBot, Agobot, Gaobot”
++++++++++++++++++++++++++++++++++++++++++++++++++ ++++++++++++++++++++++++++++++++++++++++++++++++++ +++++++++++++++++++++

#MatikanPort yang Biasa di pakai Spam :
/ip firewall filter add chain=forward dst-port=135-139 protocol=tcp action=drop
/ip firewall filter add chain=forward dst-port=135-139 protocol=udp action=drop
/ip firewall filter add chain=forward dst-port=445 protocol=tcp action=drop
/ip firewall filter add chain=forward dst-port=445 protocol=udp action=drop
/ip firewall filter add chain=forward dst-port=593 protocol=tcp action=drop
/ip firewall filter add chain=forward dst-port=4444 protocol=tcp action=drop
/ip firewall filter add chain=forward dst-port=5554 protocol=tcp action=drop
/ip firewall filter add chain=forward dst-port=9996 protocol=tcp action=drop
/ip firewall filter add chain=forward dst-port=995-999 protocol=udp action=drop
/ip firewall filter add chain=forward dst-port=53 protocol=tcp action=drop
/ip firewall filter add chain=forward dst-port=55 protocol=tcp action=drop
/ip firewall filter add chain=forward dst-p

diatas di cek di websitenya lagi : http://www.mikrotik.com/documentation/manual_2.7/
http://www.mikrotik.com/docs/ros/2.9/ip/webproxy

lihat di system resource
dan 2/3 dari system resource di gunakan atau di alokasikan untuk : system resource print

************************************************** ******************************************
Graphing /tool graphing set store-every=hour[admin@MikroTik] tool graphing> print store-every: hour[admin@MikroTik] tool graphing> [admin@MikroTik] tool graphing interface> add interface=ether1 \allow-address=192.168.0.0/24 store-on-disk=yes[admin@MikroTik] tool graphing interface> printFlags: X – disabled # INTERFACE ALLOW-ADDRESS STORE-ON-DISK 0 ether1 192.168.0.0/24 yes[admin@MikroTik] tool graphing interface> [admin@VLP InWay] tool graphing> export
# oct/12/2005 09:51:23 by RouterOS 2.9.5
# software id = 1TLC-xxx
#
/ tool graphing
set store-every=5min
/ tool graphing queue
add simple-queue=all allow-address=10.8.2.99/32 store-on-disk=yes allow-target=yes disabled=no
/ tool graphing resource
add allow-address=0.0.0.0/0 store-on-disk=yes disabled=no
/ tool graphing interface
add interface=Inway allow-address=0.0.0.0/0 store-on-disk=yes disabled=no
add interface=LAN allow-address=0.0.0.0/0 store-on-disk=yes disabled=no
add interface=DMZ allow-address=0.0.0.0/0 store-on-disk=yes disabled=no

1. Configuration position of ADSL connection
modem —Mikrotik—-Switch —– Client
|
Client

a. Modem IP –>> 192.168.1.1

b. Mikrotik Using 2 Interface – Ether1 —->> 192.168.1.2

- Ether1 —->> 192.168.0.254

c. Switch — Client ip 192.168.0.1-253

2. Configuration step router pc mikrotik

a. add ip address to interface 1

/ip address add interface=ether1 address = 192.168.1.1 netmask= 255.255.255.0

b. add ip address to interface2

/ip address add interface=ether2 address = 192.168.0.1 netmask= 255.255.255.0

c. to see input of interface

/interface print

d. Set Value name off interface

/inteface set 0 name=”Public” –>> For Modem
/inteface set 1 name=”Lan” –>> For Lan

e. set routing for net ( modem )

/ip route add gateway=192.168.0.1

f. set dns server ISP

/ip dns set primary-dns=203.130.193.74 secondary-dns=202.134.0.155

/ip dns set allow-remote-requests=yes

g. set of nat the router pc to sharing bw to lan

/ip firewall nat add chain=srcnat out-inteface=Public action=masquerade

1. first se t web proxy
/ ip web-proxy
set enabled=yes –>> to make ip web proxy enable
set src-address=0.0.0.0 –>> to make source address to access web proxy will allow
set port=8080 –>> to make port for web proxy
set hostname=”proxy.war.net.id” –>> setting for visble hostname web proxy
set transparent-proxy=yes –>> make transparant proxy enable
set parent-proxy=0.0.0.0:0–>> if we used parent proxy x
set cache-administrator=”support@somethink.org” –>> make set administrator info support
set max-object-size=4096KiB –>> maximal object can cacth with the proxy server
set cache-drive=system –>> where drive position that cache wil be saved
set max-cache-size=unlimited –>> maximal harddrive we used for cache
set max-ram-cache-size=unlimited –>> maximal ram we used for cache

2. add nat for redirect port for squid to make transparant

/ip firewall nat add chain=dstnat protocol=tcp dst-port=80 action=redirect to-ports=8080 –>> setting can redirect port 80 to 8080 for proxy server
/ip firewall nat add chain=dstnat protocol=tcp dst-port=3128 action=redirect to-ports=8080 –>> setting can redirect port 3128 to 8080 for proxy server
/ip firewall nat add chain=dstnat protocol=tcp dst-port=8080 action=redirect to-ports=8080 –>> setting can redirect port 8080 to 8080 for proxy server

Good Luck

regard

Ada pun fitur2 nya sbb:

* Firewall and NAT – stateful packet filtering; Peer-to-Peer protocol filtering; source and destination NAT; classification by source MAC, IP addresses (networks or a list of networks) and address types, port range, IP protocols, protocol options (ICMP type, TCP flags and MSS), interfaces, internal packet and connection marks, ToS (DSCP) byte, content, matching sequence/frequency, packet size, time and more…

* Routing – Static routing; Equal cost multi-path routing; Policy based routing (classification done in firewall); RIP v1 / v2, OSPF v2, BGP v4

* Data Rate Management – Hierarchical HTB QoS system with bursts; per IP / protocol / subnet / port / firewall mark; PCQ, RED, SFQ, FIFO queue; CIR, MIR, contention ratios, dynamic client rate equalizing (PCQ), bursts, Peer-to-Peer protocol limitation

* HotSpot – HotSpot Gateway with RADIUS authentication and accounting; true Plug-and-Play access for network users; data rate limitation; differentiated firewall; traffic quota; real-time status information; walled-garden; customized HTML login pages; iPass support; SSL secure authentication; advertisement support

* Point-to-Point tunneling protocols – PPTP, PPPoE and L2TP Access Concentrators and clients; PAP, CHAP, MSCHAPv1 and MSCHAPv2 authentication protocols; RADIUS authentication and accounting; MPPE encryption; compression for PPPoE; data rate limitation; differentiated firewall; PPPoE dial on demand

* Simple tunnels – IPIP tunnels, EoIP (Ethernet over IP)

* IPsec – IP security AH and ESP protocols; MODP Diffie-Hellman groups 1,2,5; MD5 and SHA1 hashing algorithms; DES, 3DES, AES-128, AES-192, AES-256 encryption algorithms; Perfect Forwarding Secrecy (PFS) MODP groups 1,2,5

* Proxy – FTP and HTTP caching proxy server; HTTPS proxy; transparent DNS and HTTP proxying; SOCKS protocol support; DNS static entries; support for caching on a separate drive; access control lists; caching lists; parent proxy support

* DHCP – DHCP server per interface; DHCP relay; DHCP client; multiple DHCP networks; static and dynamic DHCP leases; RADIUS support

* VRRP – VRRP protocol for high availability

* UPnP – Universal Plug-and-Play support

* NTP – Network Time Protocol server and client; synchronization with
GPS system

* Monitoring/Accounting – IP traffic accounting, firewall actions logging, statistics graphs accessible via HTTP

* SNMP – read-only access

* M3P – MikroTik Packet Packer Protocol for Wireless links and Ethernet

* MNDP – MikroTik Neighbor Discovery Protocol; also supports Cisco Discovery Protocol (CDP)

* Tools – ping; traceroute; bandwidth test; ping flood; telnet; SSH; packet sniffer; Dynamic DNS update tool

Layer 2 connectivity:

* Wireless – IEEE802.11a/b/g wireless client and access point (AP) modes; Nstreme and Nstreme2 proprietary protocols; Wireless Distribution System (WDS) support; virtual AP; 40 and 104 bit WEP; WPA pre-shared key authentication; access control list; authentication with RADIUS server; roaming (for wireless client); AP bridging

* Bridge – spanning tree protocol; multiple bridge interfaces; bridge firewalling, MAC

* VLAN – IEEE802.1q Virtual LAN support on Ethernet and wireless links; multiple VLANs; VLAN bridging

* Synchronous – V.35, V.24, E1/T1, X.21, DS3 (T3) media types; sync-PPP, Cisco HDLC, Frame Relay line protocols; ANSI-617d (ANDI or annex D) and Q933a (CCITT or annex A) Frame Relay LMI types

* Asynchronous – s*r*al PPP dial-in / dial-out; PAP, CHAP, MSCHAPv1 and MSCHAPv2 authentication protocols; RADIUS authentication and accounting; onboard s*r*al ports; modem pool with up to 128 ports; dial on demand

* ISDN – ISDN dial-in / dial-out; PAP, CHAP, MSCHAPv1 and MSCHAPv2 authentication protocols; RADIUS authentication and accounting; 128K bundle support; Cisco HDLC, x75i, x75ui, x75bui line protocols; dial on demand

* SDSL – Single-line DSL support; line termination and network termination modes

Instalasi dapat dilakukan pada Standard computer PC yang akan dijadikan router dan tidak memerlukan resource yang cukup besar untuk penggunaan standard, misalnya hanya sebagai gateway.

Berikut spec_minimal nya :

* CPU dan motherboard – bisa dgn P1 ~ P4, AMD, cyrix asal yang bukan multi-prosesor

* RAM – minimum 32 MiB, maximum 1 GiB; 64 MiB atau lebih sangat dianjurkan, kalau mau sekalian dibuat proxy , dianjurkan 1GB… perbandingannya, 15MB di memori ada 1GB di proxy..

* HDD minimal 128MB parallel ATA atau Compact Flash, tidak dianjurkan menggunakan UFD, SCSI, apa lagi S-ATA (mungkin nanti Ver. 3.0)

* NIC 10/100 atau 100/1000

Untuk keperluan beban yang besar ( network yang kompleks, routing yang rumit dll) disarankan untuk mempertimbangkan pemilihan resource PC yang memadai.

Lebih lengkap bisa dilihat di www.mikrotik.com. Meskipun demikian Mikrotik bukanlah free software, artinya kita harus membeli licensi terhadap segala fasiltas yang disediakan. Free trial hanya untuk 24 jam saja.

Kita bisa membeli software MikroTik dalam bentuk “licence” di CITRAWEB, UFOAKSES, PC24 (atau download cracknya, he he he …) yang diinstall pada HardDisk yang sebelumnya download/dibuat MikroTik RouterOS ISO kekeping CD atau disk on module (DOM). Jika kita membeli DOM tidak perlu install tetapi tinggal pasang DOM pada slot IDE PC kita.

Langkah-langkah berikut adalah dasar-dasar setup mikrotik yang dikonfigurasikan untuk jaringan
sederhana sebagai gateway server.

1. Langkah pertama adalah install Mikrotik RouterOS pada PC atau pasang DOM.

2. Login Pada Mikrotik Routers melalui console :

MikroTik v2.9.39

Login: admin

Password: (kosongkan)

Sampai langkah ini kita sudah bisa masuk pada mesin Mikrotik. User default adalah admin dan tanpa password, tinggal ketik admin kemudian tekan tombol enter.

3. Untuk keamanan ganti password default

[admin@Mikrotik] > password

old password: *****

new password: *****

retype new password: *****

[admin@ Mikrotik] >

4. Mengganti nama Mikrotik Router, pada langkah ini nama server akan kita ganti menjadi
“r-WLI” (bebas, disesuaikan dengan nama jaringan kita…)

[admin@Mikrotik] > system identity set name=r-WLI

[admin@r-WLI] >

5. Melihat interface pada Mikrotik Router

[admin@r-WLI] > interface print

Flags: X – disabled, D – dynamic, R – running

# NAME TYPE RX-RATE TX-RATE MTU

0 R ether1 ether 0 0 1500

1 R ether2 ether 0 0 1500

[admin@r-WLI] >

6. Memberikan IP address pada interface Mikrotik. Misalkan ether1 akan kita gunakan untuk koneksi ke Internet dengan IP 192.168.0.1 dan ether2 akan kita gunakan untuk network local kita dengan IP 172.16.0.1

[admin@r-WLI] > ip address add address=192.168.0.1 /

netmask=255.255.255.0 interface=ether1

[admin@r-WLI] > ip address add address=172.16.0.1 /

netmask=255.255.255.0 interface=ether2

7. Melihat konfigurasi IP address yang sudah kita berikan

[admin@r-WLI] >ip address print

Flags: X – disabled, I – invalid, D – dynamic

# ADDRESS NETWORK BROADCAST INTERFACE

0 192.168.0.1/24 192.168.0.0 192.168.0.63 ether1

1 172.16.0.1/24 172.16.0.0 172.16.0.255 ether2

[admin@r-WLI] >

8. Memberikan default Gateway, diasumsikan gateway untuk koneksi internet adalah 192.168.0.254

[admin@r-WLI] > /ip route add gateway=192.168.0.254

9. Melihat Tabel routing pada Mikrotik Routers

[admin@r-WLI] > ip route print

Flags: X – disabled, A – active, D – dynamic,

C – connect, S – static, r – rip, b – bgp, o – ospf

# DST-ADDRESS PREF-SRC G GATEWAY DISTANCE INTERFACE

0 ADC 172.16.0.0/24 172.16.0.1 ether2

1 ADC 192.168.0.0/26 192.168.0.1 ether1

2 A S 0.0.0.0/0 r 192.168.0.254 ether1

[admin@r-WLI] >

10. Tes Ping ke Gateway untuk memastikan konfigurasi sudah benar

[admin@r-WLI] > ping 192.168.0.254

192.168.0.254 64 byte ping: ttl=64 time

11. Setup DNS pada Mikrotik Routers

[admin@r-WLI] > ip dns set primary-dns=192.168.0.10 /

allow-remoterequests=no

[admin@r-WLI] > ip dns set secondary-dns=192.168.0.11 /

allow-remoterequests=no

12. Melihat konfigurasi DNS

[admin@r-WLI] ip dns> pr

primary-dns: 192.168.0.10

secondary-dns: 192.168.0.11

allow-remote-requests: no

cache-size: 2048KiB

cache-max-ttl: 1w

cache-used: 21KiB

[admin@r-WLI] ip dns>

13. Tes untuk akses domain, misalnya dengan ping nama domain

[admin@r-WLI] > ping yahoo.com

216.109.112.135 64 byte ping: ttl=48 time=250 ms
10 packets transmitted, 10 packets received, 0% packet loss
round-trip min/avg/max = 571/571.0/571 ms
[admin@r-WLI] >

Jika sudah berhasil reply berarti seting DNS sudah benar.

14. Setup Masquerading, Jika Mikrotik akan kita pergunakan sebagai gateway server maka agar client computer pada network dapat terkoneksi ke internet perlu kita masquerading.

[admin@r-WLI]> ip firewall nat add action=masquerade /

outinterface=ether1 chain:srcnat

[admin@r-WLI] >

15. Melihat konfigurasi Masquerading

[admin@r-WLI]ip firewall nat print

Flags: X – disabled, I – invalid, D – dynamic

0 chain=srcnat out-interface=ether1 action=masquerade

[admin@r-WLI] >

Setelah langkah ini bisa dilakukan pemeriksaan untuk koneksi dari jaringan local. Dan jika berhasil berarti kita sudah berhasil melakukan instalasi MikroTik Router sebagai Gateway server. Setelah terkoneksi dengan jaringan Mikrotik dapat dimanage menggunakan WinBox yang bisa didownload dari MikroTik.com atau dari server mikrotik kita.

Misal Ip address server mikrotik kita 192.168.0.1, via browser buka http://192.168.0.1 dan download WinBox dari situ.
Jika kita menginginkan client mendapatkan IP address secara otomatis maka perlu kita setup dhcp server pada Mikrotik. Berikut langkah-langkahnya :

1. Buat IP address pool
/ip pool add name=dhcp-pool ranges=172.16.0.10-172.16.0.20

2. Tambahkan DHCP Network dan gatewaynya yang akan didistribusikan ke client Pada contoh ini networknya adalah 172.16.0.0/24 dan gatewaynya 172.16.0.1
/ip dhcp-server network add address=172.16.0.0/24 gateway=172.16.0.1

3. Tambahkan DHCP Server ( pada contoh ini dhcp diterapkan pada interface ether2 )
/ip dhcp-server add interface=ether2 address-pool=dhcp-pool

4. Lihat status DHCP server

[admin@r-WLI] > ip dhcp-server pr

Flags: X – disabled, I – invalid

# NAME INTERFACE RELAY ADDRESS-POOL LEASE-TIME ADD-ARP

x dhcp1 ether2 dhcp_pool1 4w2d yes

[admin@r-WLI] >

Tanda X menyatakan bahwa DHCP server belum enable maka perlu dienablekan terlebih dahulu pada langkah 5.

5. Jangan Lupa dibuat enable dulu dhcp servernya
/ip dhcp-server enable 0

Kemudian cek kembali dhcp-server seperti langkah 4, jika tanda X sudah tidak ada berarti sudah aktif.

6. Tes Dari client

Run dari Comman Prompt

Microsoft Windows XP [Version 5.1.2600]
(C) Copyright 1985-2001 Microsoft Corp.

C:\Documents and Settings\EsDat>ping www.yahoo.com

Pinging www.yahoo-ht3.akadns.net [69.147.114.210] with 32 bytes of data:

Reply from 124.158.129.5: bytes=32 time=34ms TTL=59
Reply from 124.158.129.5: bytes=32 time=24ms TTL=59
Reply from 124.158.129.5: bytes=32 time=41ms TTL=59
Reply from 124.158.129.5: bytes=32 time=29ms TTL=59

Ping statistics for 69.147.114.210:
Packets: Sent = 4, Received = 4, Lost = 0 (0% loss),
Approximate round trip times in milli-seconds:
Minimum = 24ms, Maximum = 41ms, Average = 32ms

7. Untuk bandwith controller, bisa dengan sistem simple queue ataupun bisa dengan mangle

[admin@r-WLI] queue simple> add name=Komputer01 /

interface=ether2 target-address=172.16.0.1/24 max-limit=65536/131072

[admin@r-WLI] queue simple> add name=Komputer02 /

interface=ether2 target-address=172.16.0.2/24 max-limit=65536/131072

dan seterusnya…

lengkap nya ada disini
www.mikrotik.com/docs/ros/2.9/root/queue
linux-ip.net/articles/Traffic…/overview.html
luxik.cdi.cz/~devik/qos/htb
www.docum.org/docum.org/docs

Referensi
www.mikrotik.com
www.mikrotik.com/docs/ros/2.9

software
Code:

http://rapidshare.de/files/30739630/mikrotik.router.os.2.9.6.ISO

Langkah pertama adalah sbb :

1. Buat sebuah server Radius
/ radius add service=hotspot address=127.0.0.1 secret=123456

2. Buat profile dan set profile tersebut untuk menggunakan Radius Server
/ ip hotspot profile set hsprof1 use-radius=yes

3. Membuat scriber
/ tool user-manager customer add login="MikroTik" password="qwerty" permissions=owner

4. Tambahkan Router kita dalam hal ini localhost.
/ tool user-manager router add subscriber=MikroTik ip-address=127.0.0.1 shared-secret=123456

5. Lalu silahkan browser ke http://routeranda/userman

Source http://tutorial.multisolusi.com/2007/05/21/hotspot-mikrotik/